Page History:
| Date | Autor | Change | |
|---|---|---|---|
| 09.May 2018 | LED-man | Initital - Structure | |
| 28.May 2019 | LED-man | BOM added | |
Table of Contents
Welcome to the KIJIMI Documentation
"As Synthtopia reports, the Kijimi is inspired by the sound of the RSF Polykobol, a rare French polysynth from the late ’70s that was only available in very limited quantities. According to Instagram posts from Black Corporation, the synth will be available both pre-built and as a DIY kit."
source: http://www.factmag.com/2018/04/03/black-corporation-kijimi-synth/
Product Info:
the KIJIMI Synthesizer is a product of the Black Corparation located in Tokio.
It´s available in 2 different Version:
- DIY Kit contains 12 PCBs (mostly THT) https://www.deckardsdream.com/product/kijimi-kit-preorder-run1 (total costs for the pcbs are: $999)
- Preassambled with Case ready to use https://www.deckardsdream.com/product/kijimi-built-preorder-run1 (total costs: $3749)
The DIY kit consists of 12 PCBs:
- frontpanel board
- motherboard
- 8x voice cards
- power supply board
- connectors board
The motherboard has the MCU and DACs (digital to analogue converters used to control the analogue circuitry) preinstalled, the remaining parts you have to buy yourself from a local supplier. Some DIY shops will provide full parts kits.
Most of the remaining parts are thruhole, except for power filtering ceramic capacitors, which are large (0805 size), all same value (0.1uF) and located on the opposite side of the thruhole parts on the PCB.
The frontpanel and rack case will be supplied by DIY HUB.
BOM:
MOUSER Basket: (imported from above xls) (updated 28.May 05:40PM GMT+1)
https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=6285be713e
improved for more parts - same price, the quantity is noted as "customer note" on each bag.
Total costs of Material:
503€ plus VAT Mouser (€ incl.19% german VAT)
AS3360 100€
AS3340 80€
ssi2144 ICs (VCF) 55€
OLED 5€
Potentiometer - unknown
Noise IC 10€
IC Sockets 20€
XMOS Programmer 22€
metalparts 20€
EDGE card holder 10€
____
TOTAL around: 925€ plus potentiometers maybe 50-150€
Don´t miss the frontpanel and case from DIYHUB http://siddarthianinnovations.bigcartel.com/
please respect your local requirements/laws for a powersupply (110V AC/ 230V AC) and
doublecheck the power input jack polarity (inside +) and
the diameter of 2.1mm or 2.5mm of the plug/jack or you learn it in the hard way 
Firmware/Bootloader:
drop it here
Current identified Errors/Omissions/Errata:
| Date | Location | Identified Issue | Resolution |
|---|---|---|---|
| May 29, 2018 | BOM hw board | R119, R120, R121 not in BOm 1.02 | wait on Roman |
| May2019 | OLED DISPLAY | Double check the OLED pinout | rin case of wrong pinout - remove 2 oled pinheader puns and use a resistor leg and cable tube shrink |
Wooden Case (same as in DDRM project)
Ross Lammond (UK) http://www.lamonddesign.co.uk/index/
please note, the case can ordered in different HE, order 5HE to include a effect device or expander (an expander isn´t confirmed yet)
Gallery |
|---|
| There are no images attached to this page. |
Featured Pages
Content by label
There is no content with the specified labels