Panel | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| |||||||||||||
Projecttitel: TTSH rev3 buidling guideStatus:
Startdate: 21.Dec.2016Duedate: 31.Dec.2016
last update : 18.Jan.2017 BOM excel list - added a "approved row", website improvements06 March 2019 Mouser BOM project updated
Manufacture link: http://thehumancomparator.net/ |
due to changes in my webhosting (rootserver) costs for RAM/Backup and my worktime in Adminstration of the Server & Web Application Server it would be very helpful to use my paypal gift function, thank you
Manufacture link: http://thehumancomparator.net/ |
due to changes in my webhosting (rootserver) costs for RAM/Backup and my worktime in Adminstration of the Server & Web Application Server it would be very helpful to use my paypal gift function, thank you
Section | ||
---|---|---|
| ||
Section | ||
|
Info |
---|
This guide is complete yet ( last update on 12.Jan.2017) please check my rev.2 build guide and hardcorebuildguide, gatebooster pages, that gives you more infos and knowledge. the TTSH project isn`t for beginners ! Feel free to register a account for free, you can comment, export pages, you stay informed with pageupdates by email. send me a message if you want edit my pages, i´m looking for supporters. further i´m looking for authors too, please contact me |
Table of Contents
Table of Contents | ||||||
---|---|---|---|---|---|---|
|
Trusted Builders:
...
BOM: (Bill of material)
new BOM as Excellist BOM-list-TTSH REV8-v1.2.xlsx the lists includes all parts. (update 18.january 2017 approved section added)
The shared mouser basket from thehumancomparator is wrong (22.Dec.2016)
(this Mouser basket was provided in the 'order' eMail)
https://www.mouser.de/ProjectManager/ProjectDetail.aspx?AccessID=234c0 9ed60 old link from Jon
http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=6CEDD31990 new Mouser link from me, improved see notice field for quantity "order 10"
order the 100K resistors, 2N3906, 2N3904, 1N4148 from a local dealer to save money, make sure the 2N3904/2N3904 is from tape - for better transistor value matching.
dont miss to order the parts for the gatebooster too.
old Printable BOM as listed, (rev.2 plus additional list for filter and psu)
ttshv2BOM.pdf (mainboard pcb) - i update the list in next 2 days. (remove the above listed SMT chokes and replace with chokes from SecondFilter_BOM)
4027v2BOM.pdf (vco boards)
TTSHrev3_SecondFilter_BOMv1.1.pdf (filter board) please use matched pairs 4 pairs of 2N5087 and only matched pairs for 2N3906/2N3904 (exept the single trannys)
for the rare parts, please check thonk.co.uk
if you need matched pair trannys or single tested trannys like 2N3954/8 or others, please contact me.
further i offer a survival kit
(link to my rare parts/survival page)
dont miss to order (if you only use the mouser basket)
Speakers: Visaton SC8 (reichelt.de, tme.eu)
reverb tank https://www.banzaimusic.com/Belton-RBL2AB3C1B.html see known issues for wiring
RCA/Chinch cable 0,5m - 1m (double or triple isolated otherwise you gets hum issues)
DC Powersupply 24V/1A DC (preferred, 12V - 24V works) middle pin is + (5,5mm/2,1mm size)
Cable for Power wiring and Speaker wiring (for power ist required the usage of minimum 1mm² diameter )
13 x 12mm Spacer M3, black flat Screws for frontpanel, screws for speaker at the rear and spacermounting, washers, nuts, cable shrink, silicon for matched pairs or glue the trannys together
1 x 10mm spacer + washer for filtercard mounting (ignore the second hole for a spacer in VCF section)
3x long spacers to mount the powersupply (25mm-50mm preferred to minimize the risk of EMV issues )
Warning |
---|
as stated above, the project is NOT for beginners nearly all professional builders have standard resistor and capacitor values at home (if the BOM miss a few standard parts like a 100K resistor) |
Known Issues
...
title | Known Issues Click here to expand... |
---|
...
...
...
...
|
Info |
---|
This guide is complete yet ( last update on 18.Jan.2017) please check my rev.2 build guide and hardcorebuildguide, gatebooster pages, that gives you more infos and knowledge. the TTSH project isn`t for beginners ! Feel free to register a account for free, you can comment, export pages, you stay informed with pageupdates by email. send messages to me and other users with the share page function ( in top right corner) you can send me a message if you want edit my pages, i´m looking for supporters. further i´m looking for authors too, please contact me |
Table of Contents
Table of Contents | ||||||
---|---|---|---|---|---|---|
|
Trusted Builders:
Name | Region | Contact | |
---|---|---|---|
Fuzzbass | USA | fuzzbass "at" verizon.net | |
Elmigel | USA | Pete.hartman "at" gmail.com | |
Dave.H | USA | ishkabbible "at" gmail.com | |
LED-man | Europe/worldwide | check my Impressum |
Schematics:
http://thehumancomparator.net/wordpress/wp-content/uploads/2014/05/TTSHv3Schematics.pdf
you find the known erros/issues in "the tabs on top"
rev.3 Build Guide
Expand | ||||||
---|---|---|---|---|---|---|
| ||||||
This guide is for users with experience in SDIY, you need a scope and a frequency counter, DMM/DVM/LCR-Meter) i dont share infos about polarity of capacitors, this basics skills are required, otherwise feel free to ask me for a assembly service. (check the trusted builder list) please use a fume extractor. its needed to solder 6 SMT caps in 0805 format and 2 SMT power regulators. this guide is a best practice guide, i´m not responsible for failures/malfunctions/defects.
for power between power supply and mainboard - double-check the polarity, |
rev.3 Quick build guide ( thanks to Anthony A Flagg aka fuzzbass)
this guide is only for builders with TTSH experience, dont try it if you build a TTSH before, the guide contains a BOM with partnumbers too.
V3 quick build bom.xlsx (right click to "save as")
TTSH Trimming - calibration
Expand | ||||||
---|---|---|---|---|---|---|
|
Troubleshooting knowledge
i ran in some difficult errors in some TTSHs, here are my experiences
for unknown issues/Errors check this page: useful Documentation for Troubleshooting
Knowledge number | symptom | Probable error source | Probability of occurrence | pre check | testing | workaround | fix | lessons learned |
---|---|---|---|---|---|---|---|---|
TTSH-1 | VCO bleed (usage of frequency slider from one OSC influenced other VCOs frequency or Frequency range isn´t good enough or screaming VCO - weird frequency / instable Frequency | LFO/VCO switch (LF switch) | 80% | insert a stable v/oct signal (doublecheck with other devices your v/oct signal) | press/push/wiggle the LF switch, if you hear or measure a better result -> | heat up the 6 switch pins | normally a resolder/heatup fix the issue | the switch pins must be soldered with other soldercore or better heated/other solder tip. |
TTSH-2 | all Slider LEDs are off | Trimmer, LED Driver | turn on the frontpanel (left hand) the LED trimmer clockwise, check on the frontpanel side on the empty IC socket next that you bridged pin 6+7 and no IC is plugged inside the socket. if not fixed: measure on the 5 pole powerheader all voltages | n/a | dont forget the jumper/bridge on pin 6-7 | |||
TTSH-3 | few Slider LEDs are off | Trimmer, LED Driver | 50% | turn on the frontpanel (left hand) the LED trimmer clockwise, the TTSH LEDs are connected in 6? chains and in each chain are all slider LEDs in series - so you must check the correct LED polarisation (you can see the cathode/anode without demounting) | swap the LED to correct orientation | dont trust machines/roboter | ||
TTSH-4 | all VCOs dont work | VCO 4027 boards | 10% | are the VCO subboards correct mounted ? (check the board connectors) are the CA3046 ICs inside ? check the soldering of the board connectors | solder all VCO conenctor pins before mounting the silders, add the CA3046 while mounting the connectors to the subboards | |||
TTSH-5 | cant get a VCO sine wave in trimming/calibration process. (you get only a triangle) | VCO-2 section | 80% | check OP-amp orientation check J-FET (2N3954) instead 2N3958 | oscilloscope shows at the TRI out a Triangle - if not fix it before. | check the symmetry at first for the triangle, use gain to setup 10v then use the offset to bend the triangle spikes - they must form a corner in combination with purity. setup again 10v. its not a easy job - try it again - the trick is the combination of offset and gain not the purity ! | before you swap the 2N3954 try other ways as before by trimming the 4 trimmers , many guys swapped the working jfets.. | |
TTSH-6 | ttsh works as a drone synth (by usage of cv/gate - the ttsh plays always sound instead of note on/off control) | 80% | check your silder settings - at the VCA output mixer - only VCA output instead of VCF or VCF and VCF. | read the usermanual | ||||
TTSH-7 | by usage of the reverb function, a hum/noise occurs | 80 | see known issues - in/out silksceen is wrong check your noise is off check the wiring | use double or triple shielded cable with good RCA connectors, not the Synthcube cable "solution" the reverb distance must around 10cm or more from pcb to minimize the risk of EMV to the tank. check the grounding of signal input in the reverb, input and output must be grounded. check the cable with a rectifier test, check the soldering of the RCA connectors on the ttsh pcb. make sure you have the correct reverb type (grounding and impedance) | reverbs are very sensitive for EMV* | |||
TTSH-8 | ADSR Release time opens the VCA and at 20fader way, the releasetime is too long | 50 | check all parts for correct value, check my pictures subpage | replace the 2N5460 or 2N4392 | test all trannys before soldering | |||
TTSH-9 | sound from speakers - without OSCs enabled/installed | 30 | if the 10R resistors in the Amplifiers are hot or the MJE172 are hot, check the orientation of the MJE172 - the unlabeled side is at the white marker from the PCB. AND you have a short or defect opamp on your TTSH, which blows your MJE172 and the 10R resistors within 30seconds. you have to use a Bench power supply with current limiter, otherwise you freeze again the MJE172. you can cut at the 1UF elks the 6 pol power header - and connect it later with PC jumpers or use resistors legs to bridge the -15715V rails. | |||||
TTSH-10 | power separation - in case of POWER FAILURES or shorts | use a Labor bench with current limiter. | separate the Sections, by cutting the traces. | |||||
TTSH-11 | reverb doesn't work BL2AB3C1B | connect a cable from the black cable from left to the black cable on right side |
Best Practise:
ID | TIP | reason |
---|---|---|
1 | when you have finished the build, move 2-3 times every slider | often the sliders cause some issues, they hang - only when you have moved the sliders 2-3 times they start to normal work |
2 | use Anti Rotating washers for the 5 nuts at the component side of the PCB | |
3 | do not trust every information regarding an audio path upgrade or subs. for the LM301 | you can always use: LM101, LM201 too - they have a better temp. stability than a LM301 they are also available in SMD package and works great. if you want an audio path upgrade, contact me and you get an offer. I do not share my secrets because some companies copy this ideas for his cheap clones. I spend few days and a lot of money in testing different opamps (which mostly need addional part changes on the pcb) |
4 | MODIFICATION | "Essential" Gatebooster Mod. VCF decoupling 1uF or more "my standard" Essential plus: Electronic switch mod AR MOD ADSR Switch Audiopath upgrade 1% matched capacitors in VCF 1% 680pF Styrene in VCO High temp. drift OPamps in VCO Highend: Essiontial plus "my standard" plus: Waveshaper MOD with subosc. some additional part changes - PSU passive cooling blocks Balanced driver with XLR |
5 | why not install the MIDI mod ?? | you have a half modular system - a intern MIDI gives you only the option to connect internal 2 CV connections. if you use a Kenton MIDI Standalone Interface (PRO SOLO MK2 or 3 etc ) - you can patch to every jack you want ! like the Ringmodulator or VCA etc... |
6 | why not install the VCO SYNC option ? | the mod isn't very easy for beginners or amateurs, the most users have problems with soft sync (when the SYNC is off) and many users blown the VCO SUB boards Transistors, which are not easy to replace. ( I have spare pcbs ) and if you install the Waveshaper board your risk of some VCO/EMV bleeds are bigger than before. The main reason is the sound, there's not a big difference in sound between a Ring MOD sound and a SYNC sound !!! |
Gallery
check also the rev.3 buildguide pictures with HQ pictures ( thank you Björn Verbruggen)
Gallery | ||
---|---|---|
|
...
Minor Bug: turn 180degrees on the mainboard the 5pol MTA156 powerheader, otherwise the powercable is to the wrong side.
Tip |
---|
use 3x 20k or 25k multiturn trimmer Bourns Trimmer 3296Y-1-203LF (Y footprint instead of W, W fits to with bending the legs ) for V/OCT trimmer in the VCOs, but this must mount from the pcb parts side (not the same side as the frontpanel), you must calibrate the VCOs from rear side, but its more accurate to calibrate as with single turn trimmer |
rev.3 Build Guide
...
title | Build guide - Click here to expand... |
---|
This guide is for users with experience in SDIY, you need a scope and a frequency counter, DMM/DVM/LCR-Meter)
i dont share infos about polarity of capacitors, this basics skills are required, otherwise feel free to ask me for a assembly service. (check the trusted builder list)
please use a fume extractor.
its needed to solder 6 SMT caps in 0805 format and 2 SMT power regulators.
this guide is a best practice guide, i´m not responsible for failures/malfunctions/defects.
...
- Wire first to headphone jack, then to speaker.For the left amp :Connect pad L to tip pin, connect switching tip pin to left speaker. Connect GND pad to speaker.For the right amp :Connect pad R to ring pin, connect switching ring pin to right speaker. Connect GND pad to speaker.And finally connect sleeve pin on jack to ground somewhere on board. (external gate ground is good choice)So when headphone is inserted it breaks the connection to the speakers.
...
for power between powersupply and mainbaord - doublecheck the polarity,
TTSH Trimming - calibration
...
Gallery
Gallery | ||
---|---|---|
|
Stats